Research Journal of Chemical Sciences ______________________________________________ ISSN 2231-606X Vol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 24 Ultrasonic and Theoretical study of Binary Mixture of two Polar Liquids at Different Temperatures Mishra Sujata1 and Paikaray RitaDepartment of Physics, Paradeep College, Paradeep, Odisha, INDIA Department of Physics, Ravenshaw University, Cuttack, Odisha, INDIAAvailable online at: www.isca.in Received 1st May 2013, revised 17th May 2013, accepted 11th June 2013Abstract Ultrasonic speed and density have been determined in Dehpa (Di(2-ethyl-hexyl) phosphoric acid), n-Butyl Bromide and their mixtures at four temperatures 303K, 308K,313K, 318K over entire composition range. Different acoustic parameters and their excess values were calculated using measured value of ultrasonic velocity and density at different temperatures and have been discussed to highlight the type and extent of molecular interaction between component molecules and to reflect effect of temperature on them. Further theoretically ultrasonic speeds calculated using various theoretical models and empirical relations and validity of these theoretical approaches have been tested for the present system. Keywords: Binary liquid mixture, DEHPA, n-Butyl bromide, acoustic parameters, intermolecular interaction. Introduction The thermodynamic properties and intermolecular interactions of the binary liquid mixtures can be estimated more precisely using ultrasonic technique. The study and understanding of thermodynamic transport properties of liquid mixtures and solutions consisting polar and non-polar components are very essential for their application in chemical, textile, leather and nuclear industries. Acoustic parameters are sensitive to composition of the mixture i.e. molecular arrangement in the solution which results from inter molecular interaction. Speed of sound depends upon the structure and interactions present in the liquid system as it is fundamentally related to the binding forces between the constituents of the medium and also sensitive to temperature. The measurements of speed of sound in liquid mixtures are used to determine thermo-acoustic parameters and their excess values that are very sensitive to intermolecular interaction1-7. Dehpa is an acidic extractant widely used in the atomic energy industry. It is used for extraction of uranium, vanadium, beryllium. Yttrium, cobalt, zinc rare earths and other valuable metals. The extraction efficiency of the extractant improves with the addition of suitable organic diluents and modifiers. n-Butyl bromide is used as an alkylating agent to introduce the butyl groups to form carbon- carbon bonds in organic synthesis. They are also used as intermediate to alkylated amines and metallic compounds. Literature survey indicates that there has been no temperature- dependent study of this system from the point of view of their ultrasonic and thermodynamic behaviour. Hence, study performed on the interaction of n-Butyl bromide with DEHPA at different temperatures. Again theoretical approaches for liquids namely free length theory (CFLT), Impedance dependence relation (CIDR), Nomoto relation (CNOM), Vandeal and Vangeel relation (CVAN) and Rao’s specific sound velocity relation (C) applied to the binary system under investigation at temperature 303K to reflect the behaviour of the system by calculating the deviation of the theoretical values of sound speeds from experimental values. Material and MethodsThe ultrasonic speeds in pure liquids and liquid mixtures have been measured using an ultrasonic interferometer (model Mx-83) supplied by Mittal Enterprises, New Delhi, working at 1 MHz frequency with an accuracy of + 0.1msec-1. Binary mixtures are prepared by mixing appropriate volumes of the liquid components in the standard flasks with airtight caps and the mass measurements are performed on high precision digital balance with an accuracy of + 1mg. Density was determined by using a specific gravity bottle of capacity 25ml at different temperatures. The temperature of the sample was maintained stable by circulating thermo stated water around the interferometer cell that contains the liquid, with a circulating pump to an accuracy of + 0.1C. The experimentally measured ultrasonic speed (C) and density ) are used to calculate the derived parameters like isentropic compressibility (K), Intermolecular free length (L), molar volume (V) acoustic impedance (Z), Relative association (R), Interaction parameter () and excess parameters by using the following expressions discussed by Ali and Nain and Bahl and Bhat8,9. = 1 / (1) = k (K1/2 (2) = (x M1 + x M )/ mix (3) R= ( o) (C/C) 1/3 (4) Z = C (5) = ( Cexp/Cideal)-1 (6) = 6.3 x 10-43/2 (7) Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 25 Where C ideal = x + x2 is ideal mixing velocity, excess parameters have been calculated from the following equation = Aexp – ( x + x A) (8) Where x and x are mole fractions of DEHPA and n- Butyl bromide, = density of Dehpa C = Ultrasonic velocity in pure Dehpa at particular temperature, mixdensity of mixture M and 2 are molecular weight of Dehpa and n-Butyl bromide, k is temperature dependent constant. (Jacobson’s constant) [ value, 93.875 + 0.375T ) x 10-8 , T is absolute temperature, AE stands for excess property of parameters ( C, K, L, V, ZE ) The theoretical values of sound speeds are evaluated using the following relations taken from literature10. FLT = k / L(mix) exp1/2 (9) Where (mix) is ideal free length of mixture. NOM = [ x +x / x + x V (10) Where , = C1/3 and V represents mole fraction, molar sound speed and molar volume respectively. Suffix 1 represent st component and suffix 2 represent 2 component. IDR = Zi / / x i i (11) Where x Zi and i are the mole fraction, acoustic impedance and density of the ith component respectively. = ( x ri (12) Where r = C1/3i in the Rao’s specific sound velocity of the ithcomponent of the mixture. The sound speed in mixture is given by Van Deal and Vangeel ideal mixing relation [ 1/(x+x]1/Cmix = x/M+x/M C2 (13) The percentage of deviation in sound velocity can be calculated by using the relation (C/C)%=(Cexp-Ctheo / Cexp) X 100 Results and Discussions The measured values of density ( ) and Sound speed (C) has been used to calculate various thermodynamic parameters and their excess values using equation 1-7 for the system under investigation at temperature range 303-318K. The experimental and derived parameters are reported in table-1 and table-2. Excess parameters are listed in table-3 and table-4. Table-5 compares theoretical and experimental values of sound speed and deviations of these theories from experimental sound speeds at temperature 303K taken for study. Table- 1 Experimental parameters (, C) and derived parameters (Ks, Z, L, RA, V, ) for Dehpa +n-Butyl bromide system at 303,308K 1 C m/s x 103 kg m-3Ks 10-10 N-1Z 10kgm-2-110-11 m R V10-5 m mol-1N/m At 303K 0.0000 1045.5 1.2310 7.4317 1.2863 5.6566 - - 11.1307 26.2144 0.1606 1090.7 1.1954 7.0319 1.3038 5.5024 0.0016 1.2624 13.9532 27.1252 0.2657 1122.5 1.1721 6.7711 1.3156 5.3999 0.0066 1.2260 15.8931 27.7683 0.3895 1157.1 1.1446 6.5253 1.3244 5.3005 0.0071 1.1852 18.2803 28.3816 0.4535 1175.0 1.1305 6.4069 1.3283 5.2522 0.0073 1.1646 19.5580 28.6844 0.5362 1200.7 1.1121 6.2371 1.3352 5.1821 0.0120 1.1374 21.2603 29.1466 0.6063 1221.8 1.0966 6.1087 1.3398 5.1285 0.0148 1.1150 22.7462 29.5037 0.7308 1255.2 1.0690 5.9374 1.3418 5.0561 0.0128 1.0773 25.4927 29.9465 0.8061 1273.5 1.0523 5.8595 1.3401 5.0228 0.0086 1.0554. 27.2240 30.1257 0.8735 1288.2 1.0374 5.8088 1.3363 5.0010 0.0024 1.0364 28.8197 30.2174 1.0000 1321.6 1.0094 5.6720 1.3340 4.9418 - - 31.9427 30.5496 At 308K 0.0000 1023.3 1.2053 7.9231 1.2333 5.8934 - - 11.3681 24.8539 0.1606 1070.7 1.1736 7.4326 1.2565 5.7081 0.0050 1.2421 14.2124 25.9030 0.2657 1101.5 1.1530 7.1482 1.2700 5.5978 0.0074 1.2087 16.1564 26.5531 0.3895 1138.6 1.1286 6.8346 1.2850 5.4737 0.0118 1.1701 18.5395 27.3158 0.4535 1157.0 1.1160 6.6937 1.2912 5.4169 0.0127 1.1508 19.8121 27.6690 0.5362 1181.5 1.0997 6.5141 1.2992 5.3438 0.0148 1.1262 21.5001 28.1357 0.6063 1202.5 1.0859 6.3685 1.3057 5.2837 0.0171 1.1056 22.9702 28.5256 0.7308 1236.4 1.0614 6.1631 1.3123 5.1978 0.0152 1.0707 25.6752 29.0696 0.8061 1254.6 1.0466 6.0702 1.3130 5.1585 0.0104 1.0505 27.3723 29.2985 0.8735 1269.4 1.0366 5.9867 1.3158 5.1229 0.0039 1.0365 28.8419 29.5338 1.0000 1302.2 1.0085 5.8474 1.3132 5.0629 - - 31.9712 29.8553 Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 26 Figure-1 shows dimeric form of Dehpa. Figures 2-8 show variation of ultrasonic speed (C), deviation in isentropic compressibility (KS ), variation of excess free length (L ), variation of excess molar volume (V), variation of excess acoustic impedance (Z) variation of excess velocity (C) and variation of interaction parameter as a function of concentration and temperature. Figure-9 shows comparison of experimental sound velocity with theoretically calculated values at 303K. Figure-1 Figure-2 Variation of ultrasonic velocity with mole fraction of Dehpa Figure-3 Variation of interaction parameter () with mole fractiono of Dehpa Table-1 Shows that density of the mixture decreases and ultrasonic velocity increases with increase in mole fraction of Dehpa. Molecules having higher intra molecular interaction exhibit high density. Among Dehpa (density =1.0094 at 303K) and n-Butyl bromide (density =1-2310 at 303K), n-Butyl bromide is having higher intra molecular interaction. It can be expected that it may show high inter molecular interaction. Due to larger surface area of n- Butyl bromide (C-Br bond length 1.94A), the predominant dispersive interaction resulting in higher boiling point (102C) along with dipole-dipole interaction between polar (C-Br) bond11. As Bromide atom is more electronegative than carbon, the breaking of the polarized bond is more frequent in it. In monomeric Dehpa molecules there exist semi polar (P= 0 ) bond and ionisable (OH group. The strength of (P=0) group increases with increase in acidity. Due to presence of remarkable electro negative group in n-Butyl bromide and ionisable OH- group in Dehpa molecule, strong interactions which mainly of dipole-dipole type may be expected between them due to their polar nature. The reduction in density with increase in mole fraction of Dehpa suggests that the breaking of intra molecular interactions between solvent molecules by addition of solute molecules and inter molecular interaction between hetero molecules are weak in magnitude. But the increasing sound velocity figure-2 with increasing mole fraction of Dehpa gives an idea that the system is becoming more compact and it may be attributed due to large difference in molar volume between Dehpa (31.9427 x 10-5 mmol-1) and n-Butyl bromide (11.1307 x 10-5 mol-1) which allow them pack well into each other’s structure . The decrease in density with increase in temperature indicates loosening of intermolecular forces due to thermal agitation of molecules in the liquid mixture, which results decrease in sound velocity figure-2. The intermolecular free length L and compressibility Ks decreases with concentration and increases with increase in temperature, which is quite obvious from variation of sound speed in the system under consideration as K=1/. The dependence of L on C is shown in the model proposed by Eyring and Kincard12. The decrease in K and L with concentration suggests that the system is in compressed state i.e. formation of clusters of solute molecules with solvent molecule. When n-Butyl bromide mixed with Dehpa, its hydrophobic alkyl group disrupts the network of hydrogen bonds and many new dipoles are created in the medium and its compactness increases. The decreases of L with concentration suggests that the component molecules are more closer in the mixture than in the pure liquid. It indicates the presence of specific interactions such as dipole-dipole interactions, formation of charge transfer complexes, acceptor donor interaction between component molecules. It is observed from table-1, that both K and Lincreases very slowly at higher mole fraction of Dehpa (beyond 0.73 mole fraction). It indicates the magnitude of molecular interaction almost remain constant and attractive interaction decreases, which is supported by slight increasing trend of surface Tension values at higher mole fraction. Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 27 Table- 2 Experimental parameters (, C) and derived parameters (Ks , Z , L , RA , V, ) for Dehpa +n-Butyl bromide system at 313 and 318K 1 C m/s x 10 3 kg m-3Ks 10-10 N-1Z 10kgm-2-110-11 m R10-5 m mol-1N/m) At 313K 0.0000 1004.9 1.1924 8.3048 1.1982 6.0878 - - 11.4911 23.9283 0.1606 1053.4 1.1622 7.7541 1.2242 5.8825 0.0072 1.2333 14.3518 25.0305 0.2657 1084.6 1.1425 7.4405 1.2391 5.7623 0.0107 1.2027 16.3048 25.7082 0.3895 1121.6 1.1192 7.1025 1.2552 5.6299 0.0149 1.1651 18.6952 26.4834 0.4535 1140.0 1.1072 6.9496 1.2622 5.5689 0.0157 1.1464 19.9695 26.8460 0.5362 1163.8 1.0917 6.7630 1.2705 5.4937 0.0167 1.1226 21.6576 27.3038 0.6063 1185.6 1.0785 6.5963 1.2786 5.4255 0.0203 1.1021 23.1278 27.7367 0.7308 1218.5 1.0551 6.3834 1.2856 5.3373 0.0167 1.0684 25.8286 28.2709 0.8061 1237.1 1.0410 6.2768 1.2878 5.2925 0.0127 1.0489 27.5195 28.5331 0.8735 1252.4 1.0283 6.2000 1.2878 5.2600 0.0069 1.0317 29.0747 28.7117 1.0000 1283.4 1.0046 6.0434 1.2893 5.1932 - - 32.0953 29.0987 At 318K 0.0000 987.1 1.1861 8.6527 1.1707 6.2691 - - 11.5521 23.1727 0.1606 1036.0 1.1566 8.0555 1.1982 6.0489 0.0095 1.2271 14.4213 24.2949 0.2657 1068.3 1.1373 7.7043 1.2149 5.9156 0.0134 1.2003 16.3794 25.0165 0.3895 1105.9 1.1146 7.3358 1.2326 5.7724 0.0187 1.1628 18.7724 25.8233 0.4535 1124.1 1.1028 7.1761 1.2396 5.7092 0.0191 1.1443 20.0492 26.1842 0.5362 1148.1 1.0877 6.9747 1.2487 5.6285 0.0203 1.1205 21.7373 26.6548 0.6063 1169.7 1.0748 6.8002 1.2571 5.5577 0.0236 1.1006 23.2074 27.0863 0.7308 1203.3 1.0519 6.5656 1.2657 5.4609 0.0209 1.0669 25.9071 27.6603 0.8061 1221.6 1.0381 6.4550 1.2681 5.4148 0.0160 1.0477 27.5964 27.9213 0.8735 1236.5 1.0258 6.3760 1.2684 5.3815 0.0094 1.0310 29.1456 28.0971 1.0000 1266.0 1.0026 6.2230 1.2692 5.3166 - - 32.1593 28.4515 Table -3 Excess values of adiabatic compressibility ( KS), velocity (C) , molar volume (V) for Dehpa+ n-Butyl bromide system at temperature 303K-318K Mole fraction K E S x 10- 10 N - 1 m 2 C E m/s V E x 10 - 5 m 3 mol - 1 x 1 303K 308K 313K 318K 303K 308K 313K 318K 303K 308K 313K 318K 0.0000 0.0000 0.0000 0.0000 0.0000 0.0 0.0 0.0 0.0 0.0000 0.0000 0.0000 0.0000 0.1606 -0.1171 -0.1571 -0.1875 -0.2069 0.9 2.7 3.8 4.9 -0.5199 -0.4645 -0.4483 -0.4403 0.2657 -0.1930 -0.2233 -0.2634 -0.3028 3.7 4.1 5.8 7.1 -0.7673 -0.6859 -0.6607 -0.6480 0.3895 -0.2209 -0.2800 -0.3214 -0.3705 4.1 6.7 8.3 10.2 -0.9567 -0.8535 -0.8212 -0.8062 0.4535 -0.2267 -0.2880 -0.3296 -0.3747 4.3 7.3 8.9 10.6 -1.0109 -0.8995 -0.8655 -0.8482 0.5362 -0.2510 -0.2960 -0.3292 -0.3751 7.2 8.7 9.6 11.5 -1.0297 -0.9154 -0.8812 -0.8644 0.6063 -0.2560 -0.2961 -0.3374 -0.3793 9.0 10.2 11.9 13.6 -1.0029 -0.8895 -0.8556 -0.8388 0.7308 -0.2083 -0.2430 -0.2687 -0.3114 8.0 9.3 10.1 12.4 -0.8473 -0.7495 -0.7200 -0.7047 0.8061 -0.1537 -0.1796 -0.2050 -0.2391 5.5 6.5 7.8 9.7 -0.6832 -0.6039 -0.5806 -0.5671 0.8735 -0.0858 -0.1232 -0.1294 -0.1543 1.6 2.5 4.3 5.8 -0.4903 -0.5230 -0.4141 -0.4069 1.0000 0.0000 0.0000 0.0000 0.0000 0.0 0.0 0.0 0.0 0.0000 0.0000 0.0000 0.0000 Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 28 Table-4 Excess values of free length (Lf), acoustic impedance (Z ) for Dehpa+ n-Butyl bromide system at temperature 303K-318K Mole fraction L E f x 10 - 11 m Z E x 10 6 kgm - 2 s - 1 x 1 303K 308K 313K 318K 303K 308K 313K 318K 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.1606 -0.0394 -0.0519 -0.0616 -0.0672 0.0098 0.0103 0.0113 0.0116 0.2657 -0.0672 -0.0749 -0.0878 -0.1004 0.0150 0.0154 0.0170 0.0180 0.3895 -0.0776 -0.0962 -0.1094 -0.1257 0.0195 0.0205 0.0215 0.0235 0.4535 -0.0802 -0.0998 -0.1131 -0.1279 0.0203 0.0216 0.0226 0.0242 0.5362 -0.0912 -0.1042 -0.1144 -0.1298 0.0233 0.0233 0.0234 0.0251 0.6063 -0.0947 -0.1061 -0.1199 -0.1338 0.0245 0.0247 0.0251 0.0266 0.7308 -0.0781. -0.0886 -0.0967 -0.1121 0.0206 0.0206 0.0208 0.0230 0.8061 -0.0575 -0.0654. -0.0741 -0.0864 0.0153 0.0156 0.0161 0.0179 0.8735 -0.0312 -0.0450 -0.0463 -0.0555 0.0083 0.0127 0.0100 0.0116 1.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 Table-5Application of various theoretical approaches and percentage of deviation for Dehpa + n-Butyl bromide system at 303K Mole fraction C/C % (X) EXP ms-1 NOM ms-1 IDR ms-1 FLT ms-1 R MS VAN ms-1NOM CIDR FLT CVAN 0.0000 1045.5 1045.5 1045.5 1045.5 1045.5 1045.5 0.0000 0.0000 0.0000 0.0000 0.0000 0.1606 1090.7 1138.4 1082.9 1085.8 1111.9 1008.9 -4.3733 0.7151 0.4492 -1.9437 7.4997 0.2657 1122.5 1180.7 1108.6 1110.2 1151.6 1006.5 -5.1848 1.2383 1.0957 -2.5924 10.334 0.3895 1157.0 1219.0 1140.3 1141.9 1193.7 1001.3 -5.4124 1.4093 1.2709 -3.2076 13.427 0.4535 1175.0 1235.4 1157.2 1158.5 1213.9 1007.7 -5.1404 1.5148 1.4042 -3.3106 14.2382 0.5362 1200.7 1253.7 1179.9 1181.6 1237.2 1022.1 -4.4140 1.7323 1.5907 -3.0398 14.874 0.6063 121.8 1267.3 1199.5 1200.8 1255.4 1040.2 -3.7240 1.8251 1.7187 -2.7500 14.863 0.7308 1255.2 1287.8 1236.0 1240.2 1282.9 1088.9 -2.5971 1.5296 1.2029 -2.2068 13.248 0.8061 1273.5 1298.6 1258.9 1260.6 1296.5 1131.7 -1.9709 1.1385 1.0129 -1.8060 11.134 0.8735 1288.2 1307.3 1280.1 1280.8 1307.0 1181.7 -1.4826 0.6287 0.5744 -1.4594 8.267 1.0000 1321.6 1321.6 1321.6 1321.6 1321.6 1321.6 0.0000 0.0000 0.0000 0.0000 0.0000 Figure-4 Variation of deviation in isentropic compressibility (K) with mole Fraction of Dehpa Figure-5 Variation of excess intermolecular free length (L) with mole fraction of Dehpa Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 29 The relative association R is a function of ultrasonic velocity. It is influenced by two factors. The breaking of solvent structures on addition of solutes to it and the solvation of solutes. The first possibility results decrease in R and second possibility results increase in R. The continuous decrease in Rwith concentration of Dehpa indicates the breaking up of the solvent structure table-1. It may be noticed that the value of Rremain almost unchanged in higher mole fraction of Dehpa, which is supported by decrease of interaction parameter figure-3. It implies that the interaction become weaker at higher mole fraction of Dehpa. It is interesting to note that R shows decreasing trend and shows increasing trend with increase in temperature at all concentrations. Increase in temperature promotes increase in distance between surface of two molecules and hence increase in L, which favours decrease in repulsive forces and increase of dipole-dipole interaction. Excess thermodynamic parameters: The deviation of a physical property of the liquid mixture from the ideal behaviour is a measure of the interaction between molecules, which is attributed to either adhesive or cohesive forces. Thus the study of excess parameters play an important role to highlight the presence of molecular interaction between unlike components in a liquid mixture. The strength of the interaction between the components is greater when excess value tend to become increasingly negative. The variation of deviation in isentropic compressibility K with mole fraction of Dehpa at all four temperatures are shown in figure-4. Deviation in isentropic compressibility is negative over the entire composition range of mixtures with a peak value at 0.60 mole fraction at all temperatures. This indicates specific interactions that is mainly of dipole type existing between component molecules. The negative values of excess isentropic compressibility indicate that the liquid mixture is less compressible than pure liquids forming solution and molecules are more tightly bound in liquid mixture than in the pure liquid. Similar observations are found in literature13-15. The variation of excess intermolecular free length L is similar to that of KS with negative deviation having peak value at 0.60 mole fraction over the entire range of composition in all four temperatures figure-5. This indicates structural re-adjustment of component molecules in the liquid mixture and close packing of molecules.At 0.60 mole fraction of Dehpa, both Lf and KS clearly indicates that the Bromide group has more electro negative centre, which form strong interaction with positive centre of Dehpa. Hence, interaction becomes maximum when peak of KS and L occur. When temperature increases KS and L becomes more and more negative in the present system. Increase in temperature promotes the breaking of associates present in the pure liquids releasing more and more free dipoles of unlike molecules in the mixture which interact with each other As a result, excess values become more negative with rise in temperature. Studies shown that K and Lf become increasingly negative as the strength of interaction between component molecules increases. But the less magnitude of L itself suggests that there is a possibility of some weak interactive forces present in the system. The decrease in K and L with increase in concentration indicates the weakening of interaction at higher mole fraction region. The excess molar volume V is negative over the entire composition range of mixtures with a peak at about 0.53 mole fraction as shown in figure-6. This suggests the component molecules are more close together in the liquid mixture than the pure liquids forming the mixture at equimolar concentration region. Hence, attractive interaction between component molecules such as dipole-dipole and acceptor-donor interactions are present between unlike molecules. Another probable source of negative contribution is the difference in sizes and shapes of the component molecules allowing them to fit into each others structure. Structural effects arising from the interstitial accommodation due to differences in molar volume and free volume between liquid components contributes to negative VE values. Due to well fitting of component molecules into each others structure, the volume of the mixture decreases which results negative excess isentropic compressibility and negative excess molar volume. Again considering the effect of temperature it is clear from the figure-6 that VE values decreases with increase of temperatures i.e. dV / dT is positive. This indicates the dipole-dipole interaction between hetero molecules increases leading to contraction in volume.Several workers observed similar trends of this behaviour which can be attributed mainly due to specific interaction between unlike molecules of the system15-18. The value of ZE is positive over entire composition range as shown in figure-7. It agrees with the results from KS and V. It indicates association of molecules in the present system and more than one type of interaction i.e. predominant dipole-dipole interaction with weak dispersion forces present in the system. The excess ultrasonic speed C figure-8 is positive at all temperatures taken for study. Positive deviation in CE suggests the presence of strong interaction between the component molecules. At higher temperatures the increasing positive value of CE indicates strong interactions, which supports our view that the interactions between the component molecules are stronger at high temperatures. But less positive value of C indicates the interaction between the components weakened due to presence of other kind of forces which resists dipole-dipole interaction. Theoretical evaluation of ultrasonic speeds in liquid mixtures offers a simple and convenient method for study of the nature of molecular interactions in liquid mixtures. The theoretical values of ultrasonic speeds evaluated using Nomoto Relation, Impedance dependence relation, Rao’s specific sound velocity relation, free length theory (FLT) and Vandeal and Vangeel relation along with experimental value and percentage deviation are presented in table-5 for comparison. The deviations of experimental sound speed from theoretical value are due to limitations and approximations incorporated in these theories. Nomoto’s relation is based on additivity of molar sound velocity and isochoric condition under which volume remains unchanged even after mixing the components. Therefore no interaction between the components of liquid mixture. Impedance Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 30 dependence relation and Rao’s specific sound velocity relation is based on additivity of acoustic impedance and Rao’s specific sound velocity again no interaction between is taken into account. Free length theory (FLT) relates intermolecular free length of the liquid mixture with ideal free length. But on mixing two liquids, the interaction between the molecules of liquid takes place because presence of various types of forces such as dispersion forces, charge transfer, hydrogen bonding, dipole-dipole and dipole-induced dipole interactions. Figure-6 Variation of excess molar volume (V) with mole fraction of Dehpa Figure-7 Variation of excess acoustic impedance (Z) with mole fraction of Dehpa Negative deviations observed Table-5 in Nomoto relation and Rao’s specific sound velocity relations imply that molar sound speed and Rao’s specific sound speed are non-additive in the present system and it indicates absence of any complex formation between unlike molecules. Large positive deviations observed in Van Deal and Vangeal relation figure-9 is due to observed negative values in K and imply the compactness of the system and existence of strong dipole-dipole interaction. Positive deviations observed in impedance dependence relation and free length theory indicates non-additivity of acoustic impedance and free length which indicates strong interaction between unlike molecules. The average percentage of deviation observed in Nomoto relation is -3.8110, in free length theory is 1.1466, in impedance relation is 1.3035, in van Deal and Vangeal relation is 11.9875 and in Rao’s relation is -2.4795. From these values it is clear that free length theory is best suited for evaluation of ultrasonic velocity in the present system taken for study followed by impedance relation and Rao’s specific sound velocity relation. Figure-8 Variation of excess velocity( CE ) with mole fraction of Dehpa Figure-9 Comparison of experimental sound velocity with theoretical value at 303K Conclusion Variation of acoustic parameters with concentration indicate the presence of specific interaction which mainly of dipole-dipole interaction along with weak dispersive force in the present system. dispersive forces originate due to large surface area of both components. Variation of excess parameters with concentration indicate that strength of dipole-dipole interaction is maximum at equimolar concentration and its strength decreases with increase in concentration due to dispersive forces which basically depend upon surface area of both molecules. Acoustic parameters are highly sensitive to the temperature variation. With increase of temperature, the excess values tends to become more negative, indicate the inter molecular Research Journal of Chemical Sciences ___________________________________________________________ ISSN 2231-606XVol. 3(6), 24-31, June (2013) Res. J. Chem. Sci. International Science Congress Association 31 interaction between the components in the mixture increases. Among five theories taken to predict the ultrasonic speed in the present binary mixture at different concentrations, free length theory gives excellent comparison with experimentally determined sound speed followed by impedance relation and Rao’s specific sound velocity relation. References 1.Gangwar Munendra kumar and Saxena Assis Kumar, Ultrasonic study of molecular interaction in binary mixture of isopropyl benzene (Cumene) with benezene tulene and aceton at 303K., Res. J. chem. Sci, 3(2), 27-30 (2013)2.Saxena Dinesh, Dwivedi Bibek and Mishra Pankaj Kumar, di-electric study of polyaniline in frequency range 100Hz to 500KHz at temperature 200C and 300C, Res. J. Chem,Sci.,3(2), 16-19 (2013)3.Ravichandran S. and Ramanathan K., Acoustical properties and Surface tension study of some potassium salts in polyacrylamide solution at 303K, Res. J. Chem Sci., 2(10), 49-54 (2012)4.Gutta Sridevi, Ultrasonic study of Acoustical parameters of binary liquid mixture of methyl Benzoate with 1-Octanol at 303.15K, 308.15K, 313.15K and 318.15K, Res J Chem Sci, 3(3), 14-19 (2013)5.Sahu S., Nath G. and Paikaray R., study of molecular interaction in binary mixtures at variable frequencies using ultrasonic technique, Res J Chem Sci, 2(11), 64-66 (2012)6.Abraham Rosan, Abdul Khadar M., Ultrasonic Investigation of molecular interaction in binary mixtures of nitriles with methanol and toluene, The J Chem Thermodynamics 32(1), 1-16 (2000)7.Nath G., Sahu S. And Paikaray R., Acoustical investigation of molecular interaction in binary mixture of acetone and xylene a different frequencies, Journal of acoustical society of India, 35, 115-120 (2008) 8.Bahl A. and Bhat B.S., A Text Book of Organic chemistry, 17th Edn, S. Chand and Company, 2 (2005) 9.Ali A. and Nain A.K., Ultrasonic study of molecular interaction in binary liquid mixtures at 30c, pramana, (58),695-704 (2002) 10.Sravan Kumar D. and Rao Krishna, Study of molecular interactions and ultrasonic velocity in mixtures of some alkanols with aqueous propylene glycol, Indian J Pure & Applied physics 45(3), 210-220 (2007) 11.Wade L.G. and Singh M.K., organic chemistry, pearson education, 6th edition, ISBN 81-7758-739-0 (2006) 12.Kincaid J.F. and Eyring H., Free volumes and free angle rations of molecules in liquid, J. Chem. Phy, (6), 620-629 (1938) 13.Mehera Rita and Pancholi Meenakshi, study of molecular interactions in binary mixtures of benzene-butanol and toluene-butanol systems from acoustic and thermodynamic parameters, Indian J pure & Appl phys,(45), 580-590 (2007) 14.Mishra S. and Paikaray R., Study of Molecular interaction and Association in binary mixture of DEHPA with n- Butyl chloride at different temperatures, Journal of Acoustic Soc.India, 37(1), 20-24 (2010) 15.Kumar R., Jayakumar S and Kannappan V., Study of molecular interactions in binary liquid mixture, Ind J pure & Appl Phys, (46),169-175 (2008) 16.Pravakar S. and Rajagopal L., Study of molecular interactions in aprotic-aprotic binary mixtures through ultrasonic measurement, J Pure & Appl Ultrasonics, 27, 41-48 (2005) 17.Nithya G., Thanuja B., C. Charles and Kanagam, Study of intermolecular interactions in binary mixture of 2-chloro-4-methoxy-3nitro benzyl in various solvents and at different concentrations by the measurements of acoustic properties, Ultrasonic sono chemistry, (20), 65-270(2013) 18.Nain A.K., Choudhary P, and Srivastava A.K., Evaluation of Excess internal pressure, Excess free volumes and other Excess thermodynamic parameters of fermamide +1-Butanol, 2-Butanol, 1.3-Butanediol and 1,4-Butanediol mixtures from ultrasonic speed & density data, J. Acoustic Soc.India., (37)),25-32 (2010)