Research Journal of Chemical Sciences ______________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.Sci. International Science Congress Association 75 Liquid-Liquid Extraction and Separation of Cobalt(II) from Sodium Acetate media using Cyanex 272 Nikam G.H.1,2 and Mohite B.S.* Analytical and Environmental Research Lab, Department of Chemistry,Shivaji University, Kolhapur-416004, MH, INDIA PG Department of Chemistry, Jaysingpur College, Jaysingpur, Dist.-Kolhapur, MH, INDIA Available online at: www.isca.in (Received 29th November 2011, revised 15th December 2011, accepted 20th December 2011)Abstract A simple liquid-liquid extraction method has been developed for the quantitative extraction of cobalt(II) from an aqueous solution of 0.5 M sodium acetate using cyanex 272 [bis (2,4,4-trimethyl phenyl) phosphinic acid] in toluene as extractant. Cobalt(II) was quantitatively back extracted from the organic phase using 3.0 M nitric acid. The effects of various parameters affecting the extraction equilibrium of cobalt(II) such as sodium acetate concentration, cyanex 272 concentration, equilibration time, effect of various diluents, diverse ions and stripping agents have been studied. The separation of cobalt(II) from various binary as well as multicomponent mixtures has been achieved depending on the difference in the extraction and stripping behavior towards these metals. The method was extended for the separation and determination of cobalt(II) from real samples. The reliability of method is assured by comparison of the results with those obtained using AAS. Keywords: solvent extraction, cobalt(II), cyanex 272, sodium acetate, nitric acid,Introduction Cobalt and nickel are among the most important nonferrous metals. Cobalt is not found as a native metal but is mainly obtained as a by product of nickel and copper mining activities. The main ores of cobalt are cobaltite, glucodot, smaltite etc. Cobalt(II) forms the coordination complexes which are exhibiting considerable activities towards pathogenic bacteria1,2. The extraction and separation of cobalt is of great relevance and interest with the increasing demand for this metal and its compounds. There are several methods exists for the separation of cobalt from copper and nickel. They depend on the concentration of cobalt and the exact composition of used ore. Solvent extraction appears to meet the requirements for the performance and economics to replace the conventional separation methods. For the extractive separation of cobalt, copper and nickel from aqueous solutions either oximeor organophosphorous based extractantsare often employed3,4. The various organophosphorous extractants have been preferred for separation of cobalt because of better selectivity. The separation ability of organophosphorous extractants for cobalt and nickel follows the order phosphinic acid � phosphonic acid � phosphoric acid. Recovery cobalt in presence of Mg from sulphate solution using cyanex 272 and cyanex 301 has been reported. Cobalt has been separated by supported liquid membrane and solvent extraction using cyanex 2727,8. Extraction of cobalt(II) from sulphate solution has been carrid out using cyanex 301and cyanex 3029-11. Sodium salts of several organophosphorous etractants have been used for the separation of cobalt12-14. Synergistic effect of cyanex 272 and cyanex 302 on separation of cobalt and nickel by DEHPA has been studied15. Flow sheets for recovery of cadmium, nickel and cobalt from synthetic sulphate solutions using DEHPA, cyanex 272 and cyanex 923 have been developed16,17. Extraction of cadmium, nickel and cobalt from spent Ni-Cd batteries using cyanex 272 has been studied18,19. Separation of rare earth elements, cobalt and nickel from spent nickel – metal hydride batteries using cyanex 272 has been reported20,21. Cyanex 272 has been successfully employed for the separation of cobalt and nickel from sulphate solution22-24. But no attempts have been made for the separation of the cobalt (II) from associated elements from sodium acetate media using cyanex 272. This paper reports the results from the studies on the extraction of cobalt from sodium acetate media using cyanex 272 diluted in toluene. The advantages of this method over the reported methods are, that the sodium acetate is not hazardous, the concentration of cyanex 272 required for quantitative extraction is low and a clean cut separation of Co(II) from other associated metal ions has been achieved. Material and Methods Instrumentation: An atomic absorption spectrometer (Perkin-Elmer), a digital flame photometer (PI, Model no. 041, India) and a Ziess spectrophotometer (Spekol-10, Germany) were used for the determination of concentration of metal ions in the aqueous phase. A digital pH meter (Model LI-120, ELICO, India) with a combined electrode and a wrist action mechanical flask shaker were used. Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 76 Reagents: The commercial cyanex 272, i.e. bis (2,4,4-trimethyl phenyl) phosphinic acid supplied by Cytec Canada Inc., was used as such in the study without any further purification. Standard stock solution of cobalt(II) was prepared by dissolving 2.116 g of cobaltous chloride hexahydrate (AnalaR grade, Merck) in 100 mL of doubly distilled deionised water and standardized gravimetrically by a known method25. A solution containing 50 µg/mL of cobalt(II) was prepared by appropriate dilution of the standard stock solution. Sodium acetate and toluene of analytical grade from Merck were used. General Procedure: An aliquot of cobolt(II) solution (1mL of 100 µg/mL) was mixed with sodium acetate to make it’s concentration of 0.5 M in a total volume of 10 mL of the solution. The solution was then transferred to a separating funnel; 10 mL of 0.05 M cyanex 272 in toluene was added and it was equilibrated for 10 minute on a wrist action flask shaker. The two phases were allowed to settle and separate. After separating two phases cobalt(II) was back extracted from the organic phase by shaking with 10 mL of 3.0 M nitric acid and was estimated either by AAS or spectrophotometrically with PAR at 520 nm26The concentration of Co(II) was calculated from the calibration curve. All experiments were carried out at room temperature.Results and Discussion Extraction of cobalt(II) as a function of sodium acetate concentration with cyanex 272: The optimum concentration for the quantitative extraction of cobalt was ascertained by extracting cobalt with 0.05 M cyanex 272 in toluene as the diluent. Figure 1 shows the effect of varying concentrations of sodium acetate on extraction of Co(II). The sodium acetate concentration was varied from 0.01 to 1.0 M. The results show that extraction efficiency of cobalt was increased constantly with increase in sodium acetate concentration and was quantitative (100 %) from 0.4 M sodium acetate. For further studies of cobalt(II) extraction 0.5 M sodium acetate was used. Extraction as function of Cyanex 272 concentration: In order to optimize the conditions for extraction of Co(II), cyanex 272 with varying concentration (0.001 to 0.1 M) were employed. It was found that 0.04 M cyanex 272 was sufficient for quantitative extraction of 100 µg of Co(II) from 0.5 M sodium acetate. However, in the recommended procedure 0.005 M Cyanex 272 in toluene was used to ensure the complete extraction of metal ion. Figure 2 shows the effect of varying concentrations of cyanex 272 on extraction of Co(II). 0.00.10.20.30.40.50.60.70.80.91.0102030405060708090100 Extraction, %Concentration of Sodium Acetate, MFigure-1 Effect of sodium acetate concentration on extraction of Co(II) Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 77 Period of equilibration: The extraction time of Co(II) was carried out with varying periods from 1 to 15 minutes of shaking. The extraction was completed within 5 minutes of shaking, which was employed throughout the investigation. However, prolonged shaking has no adverse effect on the extraction. Choice of stripping agents: Co(II) complexed in the organic phase was back extracted from the organic phase with various mineral acids such as nitric acid, sulphuric acid, hydrochloric acid, perchloric acid, acetic acid and hydrobromic acid. Effect of various stripping agents on extraction of Co(II) is shown in figure 3. The stripping of Co(II) was found to be quantitative with 3.0 to 8.0 M nitric acid, 7.0 to 8.0 M perchloric acid and 1.0 to 8.0 M sulphuric acid. The stripping was found to be incomplete with acetic acid, hydrobromic acid and hydrochloric acid. In the proposed method 3.0 M nitric acid was used as a strippant. 0.000.020.040.060.080.10102030405060708090100 Extraction, %Concentration of cyanex 272, MFigure-2 Effect of Cyanex 272 concentration on extraction of Co(II) Figure-3 Effect of Various stripping agents 012345678102030405060708090100 Extraction, %Concentration of stripping agent, M HCl SO HNO HClO CHCOOH HBr Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 78 Influence of various diluents: A number of solvents namely toluene, carbon tetrachloride, xylene, chloroform, tetrachloroethane, 1,2 dichloroethane and nitrobenzene were employed to discern the effect of varying nature of the organic diluents on the extraction of Co(II). The results obtained are summarized in table 1. As apparent from the data the percent extraction of Co(II) was quantitative with toluene only and it was incomplete with xylene (90 %), chloroform (39 %), tetrachloroethane (61 %), 1, 2, dichloroethane (49 %), nitrobenzene (95 %)and carbon tetrachloride (60 %). However, a definite correlation between percent extraction and dielectric constant could not be established. Table-1 Influence of various diluents on extraction of Co(II) Diluents Dielectric constant Extraction % Carbon tetrachloride 2.24 60 Xylene 2.30 90 Toluene 2.38 100 Chloroform 4.80 39 Tetrachloroethane 8.20 61 1,2 Dichloroethane 9.08 49 Nitrobenzene 34.80 95 Effect of varying concentration of cobalt(II): Figure 4 shows the effect of concentration of Co(II) on percentage of extraction. Co(II) was extracted with 10 mL of 0.05 M cyanex 272 from 0.5 M sodium aceate using toluene as a diluent. The concentration of Co(II) was varied from 100 to 1600 µg/10 mL. It was found that 10 mL of 0.05M cyanex 272 was adequate to extract Co(II) quantitatively up to 700 µg per 10 mL of sample solution. Effect of diverse ions: Different amounts of diverse ions were added to 100 µg of cobalt(II) and mixture was extracted according to procedure. The tolerance limit of an ion was taken as maximum amount causing an error not greater than ±2% in the extraction of cobalt(II). Amongst the transition metals cadmium(II), copper(II), zinc(II) and manganese(II) were co-extracted along with cobalt(II). Other d-block cations were not extracted and showed high tolerance limit. Most of the s-block, p-block and f-block cations, anions of organic and inorganic acids showed very high tolerance limit except EDTA which has 0.2 mg tolerance limit. Effect of various foreign ions on extraction of cobalt(II) is summarized in table 2. Figure-4 Effect of metal ion concentration on extraction of Co(II)02004006008001000120014001600102030405060708090100 Extraction, %Concentration of Cobalt (II), µg/10mL Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 79 Table-2 Separation of Co(II) from binary mixtures Ion Added as Tol. Limit (mg) Ion Added as Tol. Limit (mg) Li + LiCl 2 Tl 3+ Tl(NO.3H 10 Mg 2+ MgCl.6HO 3 Sb 3+ SbCl 10 K + KCl 2 Y 3+ Y(NO 15 Rb + RbCl 10 Ce 3+ CeCl.6H 2 Cs + CsCl 15 Zr 4+ Zr(NO.4H 10 Cr 6+ KCr 1 V 4+ VOSO.4H 5 Be 2+ BeSO.4H 15 Th 4+ Th(NO4.6H 5 Ca 2+ CaCl 10 Mo 6+ (NHMo24.4H 3 Sr 2+ Sr(NO 10 W 6+ NaWO.4H 5 Ba 2+ Ba(NO 10 U 6+ UO(NO.6H 5 Cu 2+ CuCl.2H Coextract Cl - HCl 15 Ni 2+ NiCl.6H 5 Br - HBr 15 Mn 2+ MnCl2.4H Coextract Oxalate Oxalic acid 15 Zn 2+ ZnCl Coextract ClO - HClO 10 La 3+ LaCl 5 SCN - NHSCN 10 Cd 2+ CdCl Coextract SO 2 - SO 15 Sn 2+ SnCl 5 BO 3 - BO 10 Fe 3+ FeCl.6H 2 Tartrate Tartaric acid 15 Al 3+ Al(SO.16HO 10 EDTA EDTA 0.2 Hg 2+ HgCl 1 Ascorbate Ascorbic acid 12 Cr 3+ Cr(NO.9HO 2 PO 3 - HPO 15 Separation of cobalt(II) from ternary mixtures: Separation of Co(II) from ternary mixtures containing commonly associated metal ions, e.g. Fe(III), Ni(II), Pb(II), V(IV) and Cu(II) was carried out by taking advantage of the differences in the extraction conditions of metal ions as shown in table 3. Ternary mixtures of Cu(II), Co(II), Fe(III); Pb(II), Co(II), Fe(III); Cu(II), Co(II), Ni(II); Pb(II), Co(II), Ni(II); Cu(II), Co(II), V(IV); Pb(II), Co(II), V(IV) were resolved by the recommended procedure of cobalt(II). Under the optimum extraction conditions of Co(II), Pb(II)/Cu(II) was quantitatively extracted into the organic phase along with cobalt(II). From the organic phase first Pb(II)/Cu(II) was stripped with 0.7 M perchloric acid, under this condition cobalt(II) was remains in organic phase. Finally cobalt(II) was stripped out with 3.0 M nitric acid. The metal contents in respective stripping phases were determined using respective spectrophotometric procedures. Ni(II), V(IV) and Fe(III) were remained unextracted in the aqueous phase, which were determined by appropriate spectrophotometric methods.Schematic representation for sequential separation of Co(II) from other associated metal ion is as shown in scheme 1. Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 80 Table-3 Separation of Co(II) from multicomponent mixtures Mixture Taken µg Found* µg Recovery* % Standard Deviation Extractant Strippant 1. Cu(II) Co(II) Fe(III) 25 50 25 24.3 49.2 24.5 97.2 98.4 98.0 0.13 0.07 0.09 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- 2. Pb(II) Co(II) Fe(III) 25 50 25 24.9 49.8 24.2 99.6 99.6 96.8 0.09 0.06 0.12 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- 3. Cu(II) Co(II) Ni(II) 25 50 25 24.3 49.7 24.9 97.2 99.4 99.6 0.11 0.09 0.08 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- 4. Pb(II) Co(II) Ni(II) 25 50 25 24.9 49.6 24.8 99.6 99.2 99.2 0.11 0.05 0.09 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- 5. Cu(II) Co(II) V(IV) 25 50 25 24.3 49.2 24.5 97.2 98.4 98.0 0.07 0.11 0.06 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- 6. Pb(II) Co(II) V(IV) 25 50 25 24.3 49.5 24.4 97.2 99.0 97.6 0.04 0.05 0.1 A A Aq. Phase 0.7 M HClO 4 3.0 M HNO 3 -- A– 0.5 M sodium acetate, 0.05 M Cyanex 272 in toluene * average of triplicate analysis Scheme-1 Sequential separation of Co(II) from multicomponent mixtures Co(II) + Cu(II)/Pb(II)+ Ni(II)/V(IV)/Fe(III) In 0.5 M sodium acetate Extraction with 0.05 M Cyanex 272 in toluene Aqueous Phase Ni(II)/V(IV)/Fe(III) Organic Phase Co(II) + Cu(II)/Pb(II) Stripped with 0.7 M HClO 4 Aqueous Phase Organic Phase Stripped with 3.0 M HNO Aqueous Phase Organic Phase Co(II) Cu(II)/Pb(II) Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 81 Separation and determination of cobalt(II) from aquatic plants: The aquatic plant sample was washed to remove periphyton, dust and sediment particles. The plant sample was dried for 8 to 10 days and heated in oven at 110C. The dried sample was grounded using mortar till finely dry powder was formed. The dried sample was weighed accurately and dissolved in nitric acid and perchloric acid mixture (3:1). The resulting mixture was evaporated to dryness and extracted with distilled deionised water. The solution was heated to boiling and filtered using Whatmann filter paper No. 1. The sample solutions of plant samples were analyzed as per the proposed method and cobalt(II) content was determined. The results obtained with proposed method shows good agreement with those obtained by AAS as shown in table 4. Table-4 Determination of cobalt(II) from aquatic plants Aquatic plant Amount of Co(II) found* g/10g Standard Deviation AAS method Proposed method Eicchornia crassipes 250.4 249.0 0.08 Hydrilla 360.6 359.5 0.05 Salvinia 410.8 409.4 0.11 * average of triplicate analysis Separation and determination of cobalt(II) from composite material samples: The proposed method was employed for the analysis of cobalt(III) in composite materials. Accurately weighed sample was treated with 10 mL aqua-regia and heated to moist dryness; the procedure was repeated for three times. Then the solution was filtered through Whatmann filter paper No.1 and diluted to 100 mL with distilled deionised water. An aliquot sample solution was analyzed as per the general procedure and cobalt content was determined. The results were in good agreement with result obtained from AAS as shown in table 5. Table - 5 Determination of cobalt(II) from composite materials Composite material Amount of Co(II) found* mg/gm Standard Deviation AAS method Proposed method ZnCoFe 2 O 4 34.12 34.01 0.10 ZnCoCeFeO 4 27.08 26.95 0.05 ZnCoLaFeO 4 24.44 24.11 0.09 * average of triplicate analysis Determination of cobalt(II) from alloys: The proposed method was applied for the determination of cobalt(II) in different alloys. Known weight of alloy was heated up to 700 C for 2 hours to remove organic matter. The sample was treated with 15 mL nitric acid and perchloric acid mixture (3:1) and heated to moist dryness, the procedure is repeated for three times. Then the solution was filtered through Whatmann filter paper No.1 and diluted to 100 mL with distilled deionised water. An aliquot sample solution was analyzed as per the general procedure and cobalt content was determined. The results were in good agreement with those obtained by atomic absorption spectroscopy as shown in table 6. Table-6 Determination of cobalt(II) from alloysAlloy Amount of Co(II) found* mg/gm Standard Deviation AAS method Proposed method Nickel based alloy (387 BCS) 101.40 101.13 0.08 Vitallium 498.45 497.61 0.12 Conclusions The present investigations have resulted in offering a convenient liquid-liquid extraction method for separation of cobalt(II). Cobalt(II) can be extracted by cyanex 272 dissolved in toluene from sodium acetate medium. The obtained results show that cyanex 272 is a potential extractant for the extraction of cobalt(II) from sodium acetate medium. This method has number of advantages over existing methods such as easy phase separation, less equilibration time and single extraction is sufficient for quantitative extraction of cobalt. Cyanex 272 extracts cobalt(II) very rapidly, equilibrium was reached within 5 minutes. Extractive separation method proposed is simple and provides a reliable means for the selective and sequential separation of cobalt(II) when present in various matrices with other metal ions. Important application of proposed method is separation of Co(II) from Co(II), Cu(II) and Ni(II) mixture, which is useful for analysis of number of alloys. The method is also useful for the extraction of cobalt(II) from real samples such as aquatic plants and composite materials. The method is simple, selective and has good reproducibility (approximately ±2%).Acknowledgment The authors are thankful to UGC-SAP and DST-FIST, Department of Chemistry, Shivaji University, Kolhapur. References1. Rakhi C. and Shelly, Synthesis spectra and pharmaceutical study of Cu(II), Ni(II) and Co(II) coordination complexes, Res. J. Chem. Sci., 1(5), 1-5 (2011) 2. Mostafa M., Metal chelates of hydrazone ligand chelating tendancies of 2carboxyphenylhydrazoacetoacetanilide (2-cphaaa) ligand, Res. J. Chem. Sci., 1(7), 1-14 (2011) Research Journal of Chemical Sciences __________________________________________________________ ISSN 2231-606X Vol. 2(1), 75-82, Jan. (2012) Res.J.Chem.SciInternational Science Congress Association 82 3. Aminian H. and Bazin C., Solvent extraction equilibria in copper(II)-iron(II)-LIX-984 system, Miner. Eng., (13), 667-672 (2000) 4. Rickelton W.A., Flett D.S. and West D.W., Cobalt and nickel separation by solvent extraction with dialkyl phosphinic acid, Proceedings of International Solvent Extraction conference, Denver, Colorado, American Institute of Chemical Engineers, New York, 195-195 (1983) 5. Pretson J.S., Solvent extraction of cobalt and nickel by organophophorous acids. I. Comparison of phosphoric, phosphonic and phosphinic acid systems, Hydrometallurgy, (9), 115-133 (1982) 6. Tsakiridis P.E. and Agatzini S.L., Process for the recovery of cobalt and nickel in the presence of magnesium from sulphate solutions by cyanex 272 and cyanex 302, Miner. Eng., (17), 913-923 (2004) 7. Swain B., Jeong J., Lee J.C. and Lee G.H., Extraction of Co(II) by supported liquid membrane and solvent extraction using cyanex 272 as an extractant: A comparison study, J. Membr. Sci., (288), 139-148 (2007) 8. Swain B., Jeong J., Lee J.C. and Lee G.H., Separation of Co(II) and Li(II) by supported liquid membrane using cyanex 272 as mobile carrier, J. Membr. Sci., (297), 253-261 (2007) 9. Ocana N. and Alguacil F.J. Cobalt-manganese separation: the extraction of Co(II) from manganese sulphate solutions by cyanex 301, J. Chem. Technol. Biotechnol.,(73), 211-216 (1998) 10. Bourget C., Jakovljevic B. and Nucciarone D., Cyanex 301 binary extractant systems in cobalt / nickel recovery from acidic sulphate solutions, Hydrometallurgy, (77), 203-218 (2005) 11. Dhadke P.M. and Ajgaonkar H.S., Liquid-liquid extraction of cobalt (II) and manganese with bis(2,4,4-trimethylpentyl) monothiophosphinic acid (cyanex 302), Indian J. Chem. Technol., 3(6), 358-362 (1996)12. Sarangi K., Reddy B.R. and Das R.P., Extraction studies of cobalt (II) and nickel (II) from chloride solution using Na-cyanex 272, Separation of Co(II)/Ni(II) by the sodium salts of DEHPA, PC88A and cyanex 272 and their mixtures, Hydrometallurgy, (52), 253-264 (1999) 13. Swain B., Jeong J., Lee J.C. and Lee G.H., Separation of cobalt and lithium from mixed sulphate solution using Na-cyanex 272, Hydrometallurgy, (84), 130-138 (2006) 14. Sahu S.K., Agrawal A., Pandey B.P. and Kumar V., Extractive separation of copper, cobalt and nickel from leach liquor of the copper concentrate using LIX 84 and Na-Cyanex 272, Miner. Eng., (17), 913-923 (2004) 15. Darvishi D., Haghshenas D.F., Alamdari E.K., Sadrnezhaad S.K. and Halali M., Synergistic effect of cyanex 272 and cyanex 302 on separation of cobalt and nickel by DEHPA, Hydrometallurgy, (77), 227-238 (2005) 16. Nogueira C.A. and Delmas F., New flowsheet for the recovery of cadmium, cobalt and nickel from spent Ni-Cd batteries by solvent extraction, Hydrometallurgy, (52), 267-287 (1999) 17. Gupta B., Deep A. and Malik P., Extraction and recovery of cadmium using cyanex 923, Hydrometallurgy, (61), 65-71 (2005) 18. Reddy B.R., Priya D.N., Rao S.V. and Radhika P., Solvent extraction and separation of Cd(II), Ni(II) and Co(II) from chloride leach liquors of spent Ni-Cd batteries using commercial organophosphorous extractants, Hydrometallurgy, (77), 253-261 (2005) 19. Reddy B.R. and Priya D.N., Chloride leaching and solvent extraction of cadmium, cobalt and nickel from spent nickel-cadmium batteries using cyanex 923 and 272, J. Power Sources, (161), 1428-1434 (2006)20. Li L., Xu S., Ju Z. and Wu F., Recovery of Ni, Co and rare earths from spent Ni-metal hydride batteries and preparation of spherical Ni(OH), Hydrometallurgy, (100), 41-46 (2009) 21. Rodrigues L. and Mansur M.B., Hydrometallurgical separation of rare earth elements, cobalt and nickel from spent nickel-metal hydride batteries, J. Power Sources, (195), 3735-3741 (2010)22. Reddy B.R. and Sharma B., Separation of Co and Ni from Sulphate solutions of Indian Ocean nodules using cyanex 272, Miner. Metall. Process, (18), 172 (2001)23. Parhi P.K., Panigrahi S., Sarangi K. and Nathsarma K.C., Separation of cobalt nickel from ammonical sulphate solution using cyanex 272, Sep. Purif. Technol., (59), 310-317 (2008) 24. Tsakiridis P.E. and Agatzini S.L., Process for the recovery of cobalt and nickel in the presence of magnesium and calcium from sulphate solutions by versatic 10 and cyanex 272, Miner. Eng., (17), 535-543 (2004)25. Vogel A.I., A textbook of quantitative inorganic analysis including elementary instrumental analysis, rd edition, The English language book society and Longman, 528 (1975)26. Pollard F.H., Hanson P. and Geary W., 4-(2-Pyridylazo)-resorcinol as a possible analytical reagent for the estimation of cobalt, lead and uranium, J. Anal. Chim. Acta, (20), 26 (1959)