I Research Journal of Environment Sciences_________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 34 Removal of Hg (II) ions from aqueous solution by Acid Acrylic Resin A Study through Adsorption isotherms AnalysisKarthika C. and Sekar M. Department of Chemistry, Sri Ramakrishna mission Vidyalaya College of Arts and Science, Coimbatore-641 020, Tamil Nadu, INDIAAvailable online at: www.isca.in Received 29th July 2012, revised 13th August 2012, accepted 14th August 2012Abstract The feasibility of using Amberlite IRC-86, a weak acid cation- exchange resin as an adsorbent for mercury (II) ions removal was examined. The influences of experimental parameters such as pH, initial mercury concentration, and agitation time and resin dosage were investigated. The data were analyzed on the basis of Lagergren pseudo-first order, Ho pseudo-second order, Langmuir, Freundlich and Redlich- Peterson isotherm models. The ion -exchange process, which is pH dependant, indicated that maximum removal of mercury (II) was obtained at pH 7±0.1 and a resin dosage of 0.1g. Through fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and scanning electron microscopy coupled energy dispersive X-ray (SEM-EDAX) analysis, the ion -exchange mechanism was confirmed. Finally, the resin can be regenerated by treatment of the spent resin with HCl. The experimental results indicate that Amberlite IRC-86, weak acid cation exchange resin is a promising adsorbent, which could be used effectively for the removal of mercury (II) ions from aqueous medium. Keywords: Amberlite IRC-86 resin, mercury (II), adsorption, isotherm, kinetics, desorption Introduction The pollution of water resources due to the indiscriminate disposal of heavy metals has been causing worldwide concern for the last few decades. The existence of heavy metals in wastewaters contributes to water toxicity and represents an increasing danger for the environment, human beings and other living organisms. Heavy metal pollution of the environment has become a growing ecological crisis and concern and therefore the subject of many researches. Mercury is well known for its extremely high toxicity and the serious threat to human life and natural environment. The drinking water criterion for mercury established by USEPA is, 2 µg/L and the permitted discharge limit of wastewater for total mercury is 10 µg/L. Therefore, it is very important to reduce the residual mercury concentration below the safety limit for mercury ions from industrial wastewater, especially from drinking water . Several methods such as evaporation, electro-deposition, solvent extraction, reverse osmosis, membrane separation process and activated carbon adsorption are employed for the removal of heavy metal ions from water waste 4. However, these techniques have certain disadvantages such as higher operational cost, requiring additional chemical, high energy consumption and residual metal sludge disposable. Due to forbidding cost of these processes, the uses of resins have been received with considerable attention. In recent years a number of commercial resins such as Amberlite IR-120, Amberlite IRC-748, Amberlite IRC-718, Lewatit TP-207 and a wide range of anion exchange resins with styrenic structures have been used to remove heavy metals from wastewater5,6,7,8. However, the applicability of cation exchange resin containing acrylic matrix for the removal of heavy metal ions from wastewater is not well documented. In the present work, the removal of Hg(II) ions from aqueous solutions using a weak acid cation exchange resin containing acrylic matrix (Amberlite IRC-86) was investigated. The aim of this work was to study the influence of experimental parameters such as pH, contact time, adsorbent dosage on Hg(II) removal and to understand the kinetics of the mechanism, thereby exploring the potential of acrylic acid resin in the removal of Hg(II) ions from the aqueous solutions. Material and Methods Ion-exchange resin: Commercial synthetic Amberlite IRC-86, weak acid cation exchange resin in hydrogen form was obtained from Sigma Aldrich Co. The properties of the resin are given in table -1. The resin was washed with double distilled water to remove impurities and dried in an oven at 80C for 24 h. Dried resin was used for further experimental studies.Preparation of standard solution: A stock solution of 1000 mg /L of Hg(II) was prepared by dissolving 1.354 g of HgCl2 in double distilled water acidified with 5ml of conc.HNO to prevent hydrolysis and diluting to 1000ml. The required lower concentrations were prepared by dilution of the stock solution, which was prepared freshly for each experiment.Fourier Transform Infrared (FTIR) and Scanning Electron Microscopy (SEM) analysis: Infrared spectra of the resins before and after ion-exchange experiment were obtained using a Fourier transform infrared spectrometer in the frequency range I Research Journal of Environment Sciences_______________________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 35 of 400-4000cm-1. With the help of scanning electron microscopy (SEM), the images of the resin surface was taken both before and after treatment with Hg(II) ions. The concentration of Hg(II) ions on the resin surface was determined by Scanning Electron Microscopy coupled energy dispersive X-ray Analysis (SEM –EDAX). Table -1 Physico-chemical properties of weakly acidic Amberlite IRC-86 resin. Characteristics Value Physical Characteristics Particle size range 16-50 mesh Temperature limitations 120 \rC Chemical Characteristics Structure Gel Matrix Acrylic Polymer Functional Group Carboxylic Acid Ionic form H + pH limitations 4 -14 Total Exchange capacity 10.7 meq /g by dry weight Matter Soluble in H 2 O (%) 4.2 meq/ml wetted bed volume Moisture retention 50% Adsorption experiments: The batch mode experiments were performed in 100ml conical flasks by addition of desired amount of resin to 50ml of Hg(II) solutions. In all experiments, the flasks were shaken at 250 rpm on the orbital shaker for predetermined time intervals at room temperature (30 ±2şC). After agitation, the resin was separated by filtration and some aliquots of filtrate in the supernatant were analyzed using spectronic 20 UV spectrophotometer at 565 nm with Rhodamine 6G . The amount of metal ion adsorbed on the resin was computed by the following equation:\n (1) Where C and C (mg/L) are the liquid -phase concentrations of solutes at the initial and equilibrium time t, respectively. V (L) is the volume of solution and W (g) is the mass of dry resin. The effect of initial pH on the removal of Hg(II) ions from aqueous solution was studied in the range of 2 to 9 pH , which was adjusted using 0.01 N HCI and 0.01 N NaOH solutions. For these experiments 50 ml of (20mg /L and 50 mg/L) Hg(II) solution was agitated with 0.1 g of resin for a period of 60 minutes. The influence of adsorbent dosage on Hg(II) removal was studied with various resin dosage (0.05 to 0.2 g/L) for 50 mg/L Hg(II) solution. Various isotherm models such as Langmuir, Freundlich, and Redlich-Peterson were investigated. Reaction-based kinetic models such as Lagergren pseudo- first order andHo pseudo - second order models were studied. The thermodynamic parameters such as free energy (), enthalpy () and entropy () changes for the sorption process were determined.Desorption Studies: Desorption studies help to elucidate the mechanism of adsorption and recovery of metal ions and adsorbent. 50ml of 20mg/L and 50 mg/L of Hg(II) ion solutions were agitated with 01.g resin for the equilibrium time. After agitation, the spent resin was treated with 50 ml of varying HCl concentration and again agitated for the predetermined time of adsorption. The desorbed Hg (II) ion solution was filtered and estimated as before. Results and discussion Effect of agitation time and initial Hg(II) ion concentration on the adsorption of Hg(II) ions from aqueous solution: Figure-1 shows the time dependant behavior of the removal of Hg(II) ions from aqueous solution by the resin. From the plot, it is clear that the removal amount of Hg(II) increased as the contact time elapsed. The equilibrium time was reached within 50 min. The initial adsorption rate was very fast which may be due to the existence of greater number of resin sites available for metal ions adsorption. As the remaining vacant surface sites decreases, the adsorption rate slowed down due to the formation of repulsive forces between the metals on the solid surface and in the liquid phase. Moreover, as the initial concentration of metal ion was increased, the percentage removal of Hg(II) ions from the aqueous solution was decreased. The kinetic curves are single, smooth and continuous, indicating the possible monolayer coverage of metal ions on the surface of the resin 10Figure-1 Effect of agitation time and initial Hg(II) ion concentration on the adsorption of Hg(II) ions by: Amberlite IRC86 resin Adsorption isotherms Langmuir isotherm: The Langmuir equation assumes that the solid surface presents a finite number of identical sites which are energetically uniform and a monolayer is formed when the solid surface reaches saturation. The linear form of the Langmuir equation is given by 11 \r  (2) Where, C is the equilibrium concentration of metal (mg/L), Qo and b are Langmuir constants related to adsorption capacity and I Research Journal of Environment Sciences_______________________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 36 adsorption energy respectively. The plot of Ce/q against C gives a straight line (figure -2) showing the applicability of Langmuir isotherm. The values of Qo and b are obtained from slope and intercept of the plot and are presented in table- 2. The essential characteristics of the Langmuir isotherm can be expressed by a dimensionless constant called, the equilibrium parameter R which perfectly determines the favorability and shape of the isotherm of the adsorption process by applying Equation -3 \r\r (3) Where, Co is the initial Hg(II) ion concentration (mg/L). As the values obtained lies between 0 and 1, the adsorption process is favorable. Figure-2 Langmuir plot for Hg(II) adsorption Freundlich isotherm: The Freundlich expression is an empirical equation based on sorption on a heterogeneous surface suggesting that binding sites are not equivalent. The linear logarithmic from Freundlich equation is as follows 12\r  (4) Where, K (mg/g) and n are constants related to adsorption capacity and adsorption intensity, respectively. Linear plots of log q versus log Ce (figure 3) showed that the adsorption obeys Freundlich isotherm. The values of K and n are presented in table- 2. Redlich - Peterson isotherm: This isotherm is a combination of Langmuir and Freundlich models which is defined as follows 13  \r (5) Where, a and K are the constant of Redlich - Peterson and is the exponent of equation which lies between 0 and 1. When =1, this equation changes to Langmuir isotherm and when =0, it changes to Henry equation which is defined as follows: \r (6)Figure-3 Freundlich plot for Hg(II) adsorption Redlich - Peterson equation can be expressed in linear form as follows: \r (7)From the plot of C versus C (figure- 4), the values of aand K were determined and are presented in table- 2. Figure-4 Plot for Redlich-Peterson isotherm Adsorption Kinetics Lagergren Pseudo - first order kinetic model: By studying adsorption kinetics, the efficiency of the absorbent was evaluated. The rate constant of adsorption was determined from Lagergren Pseudo - first order equation which is generally expressed as 14  \n\n !"! (8) Where, q and qt are the adsorption capacity (mg/g) at equilibrium and at time t, respectively and K is the rate constant for pseudo - first order adsorption. From the plots of log (q-q) against t, the values of K1 and q were determined (figure- 5) and are presented in table- 3. I Research Journal of Environment Sciences_______________________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 37 Table- 2 Isotherm parameters for removal of Hg(II) by Amberlite IRC86 resin (conditions: pH:7±0.1, volume:50 ml, resin mass: 100mg, agitation time: 60 min, temperature:303K) Isotherm models Constants Value Langmuir Q 0 ( mg/g) 70.422 b (L/mg) 0.0137 R 2 0.9933 Freundlich Hg(II) concentration 20 (mg/L) 50 (mg/L) K F (mg/g) 7.201 14.252 n 3.79 4.844 R 2 0.9201 0.9825 Redlich-Peterson K R (L/g) 0.9743 a R (L/mg) 0.0166 R 2 0.9946 Table- 3 Kinetic parameters for the removal of Hg(II) by Amberlite IRC86 resin (conditions: pH:7±0.1, volume:50 ml, resin mass: 100mg, agitation time: 60 min, temperature:303K) Pseudo-first-order model Pseudo-second-order model Conc of Hg (II) (mg/L) (mg/g) (Exp) (mg/g) (Cal) 1 x10 - 2 (1/min R 2 (mg/g) (Cal) 2 x10 - 2 (g/ mg min) R 2 10 4.583 3.755 4.987 0.9005 4.9043 2.092 0.9806 20 8.81 8.361 5.768 0.9172 9.891 0.8873 0.9761 30 13.163 13.896 5.606 0.8821 14.992 0.4783 0.9646 40 50 17.358 21.311 14.648 16.904 3.855 3.278 0.9480 0.9592 18.796 22.075 0.3754 0.3316 0.9663 0.9710 Figure-5 Pseudo-first-order Lagergren plots for Hg(II) adsorption onto Amberlite IRC86 Ho Pseudo - second order kinetic model: The linear form of Ho pseudo - second order kinetic model is expressed as15\r (9) Where, K is the rate constant of second order adsorption (g/mg/min). From the plot of t/ q against t (Figure-6), K and qwere determined and are presented in table -3. The best correlation between predicted and experimental qe values indicates that the adsorption system studied belongs to pseudo - second order kinetic model. Figure-6 Ho Pseudo-second-order plots for Hg(II) adsorption onto Amberlite IRC86 resin I Research Journal of Environment Sciences_______________________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 38 Effect of pH on Hg(II) adsorption from aqueous solution: The solution pH is an important factor controlling the surface charge of the adsorbent and the degree of ionization of the adsorbate in aqueous solution16. The effect of pH on the sorption of Hg(II) ions was tested at different pH values (2.0-8.0) using 0.1 g of Amberlite IRC - 86, weak acid cation - exchange resin for Hg(II) concentration of 20mg/L and 50 mg/L. The results indicated that the maximum uptake of Hg(II) ions occurred at initial pH of 7.0. The adsorption capacity of the resin increased with increase in pH of the aqueous solution. This can be explained on the basis of decrease in competition between protons (H+ ions) and metal cations (Hg 2+ ions ) for the same functional groups (-COO) and by decrease in the positive surface charge on the resin resulting in a lower electrostatic repulsion between the surface of resin and mercury (II) ions17. The low level of mercury (II) ions uptake at lower pH may be explained on the basis of the overall surface charge on the resin becoming positive and active sites being protonated, which will inhibit the approach of positively charged metal ions. Sorption at pH above 8.0 was not carried out to avoid any possible interference from metal precipitation in solution. Hence the optimal pH for the removal of Hg(II) from aqueous solution by the resin was found to be 7.0±0.1, which was maintained throughout the experimental studies.Effect of resin dosage on Hg (II) sorption from aqueous solution: The amount of adsorbent is one of the parameters affecting strongly the sorption capacity. The adsorption of Hg(II) ions from aqueous media on Amberlite IRC-86 resin was studied by varying amount of the ion-exchanger from 0.025 to 0.150 g at pH 7.0±0.1 for Hg(II) concentration of 20 mg/L and 50 mg/L respectively. Optimum resin dosage was fixed as 0.1g.The removal percentage increased with increase in ion - exchanger dose.Thermodynamic study: The thermodynamic equilibrium constant Kc for the adsorption of Hg(II) onto resin was determined by using the equation,  (10) Where CA is the amount of metal ion adsorbed on the adsorbent at equilibrium (mg/L) and C is the equilibrium concentration of metal ion in solution. The change in standard free energy was calculated using the following equation and its value is given in table -4. &'\n( (11) Where R is the gas constant and T is temperature (K) According to Vant Hoff’s equation, &)\n&*( (12) Where and are the changes in entropy and enthalpy of adsorption, respectively. A plot of lnK versus 1/T (Figure-7) was found to be linear. Figure-7 Vant Hoff’s plot for Hg(II) removal by Amberlite IRC86 resin The values of and were evaluated from the slope and intercept of Vant Hoff’s plot and are presented in table-4. The positive value of confirms the endothermic nature of adsorption. When the temperature increased from 303K to 323K, the magnitude of free energy change shifted to a high negative value suggesting that adsorption was rapid and spontaneous. The positive value of suggested an increase in randomness at the solid-solution interface during the adsorption of Hg(II) on resin 18. Table -4Thermodynamic parameters for the adsorption of Hg(II) by Amberlite IRC86 ((conditions: pH:7±0.1, volume:50 ml, resin mass: 100mg, agitation time: 60 min) Temperature (K) lnK c DDG [kJ/mol] DDH [kJ/mol] DDS [J/mol K] 303 1.969 4.96 18.748 0.0781 313 2.174 5.657 323 2.420 6.498 Table- 5Wave number (cm-1) for dominant peak from FTIR of resin and Hg(II) loaded resin Control frequency (cm - 1 ) of Amberlite resin Frequency of Amberlite resin after treatment with 50mg/L of Hg(II) solution (cm-1 Functional groups 2914.47 2924.47 CH stretching 1661.12 1654.65 C=C stretching 1372.16 1398.96 COO - symmetric stretching 1600.25 1637.43 COO - asymmetric stretching I Research Journal of Environment Sciences__________ Vol. 1(1), 34-41, August (2012) International Science Congress Association FTIR, SEM and SEM-EDAX analysis: The FTIR spectra of the resin and metal loaded resin (figure- 8a, 8b.) showed a shift in wave number of dominant peaks associated with the loaded metal19,20 . This shift in the wavelength indicates the metal binding process taking place at the surface of resin. Table represents the fundamental frequencies of control (resin), Hg(II) treated resin and their respective possible band frequencies in the FTIR spectra.It was stated that symmetric and asymmetric vibrations of - COO groups appeared at 1372.16 and 1600.25 cm-1, respectively21 . This observation provides evidence that the functional groups of - COO are involved in binding the Hg(II) ions onto Amberlite resin. Figure-8a FTIR spectrum of the resin Figure- 8b FTIR spectrum of Hg(II) loaded resin SEM images of the cation- exchange resin before and after Hg(II) sorption are shown in figure 9a and9b, respectively. As could be seen from the figure, a visible change of the surface Sciences__________ _____________________________ ________ International Science Congress Association The FTIR spectra of 8a, 8b.) showed a shift in wave number of dominant peaks associated with the loaded . This shift in the wavelength indicates the metal process taking place at the surface of resin. Table -5 represents the fundamental frequencies of control (resin), Hg(II) treated resin and their respective possible band frequencies in the FTIR spectra.It was stated that symmetric and asymmetric groups appeared at 1372.16 and 1600.25 . This observation provides evidence that the are involved in binding the Hg(II) FTIR spectrum of the resin FTIR spectrum of Hg(II) loaded resin exchange resin before and after 9a and9b, respectively. As could be seen from the figure, a visible change of the surface morphology in the Hg(II ) adsorbed resin demonstrated that the sorption of Hg(II) ions has taken place onto the adsorbent. Figure- 9 SEM of Amberlite IRC86 resin before Hg(II) adsorption Figure- 9b of Amberlite IRC86 resin after Hg(II) adsorption The SEM- EDAX spectrum of Hg(II) loaded resin is shown in figure- 10. The presence of Hg(II) peak in the spectrum confirms the adsorption of Hg(II) onto Amberlite resin. ________ I Res. J. Environment Sci. 39 ) adsorbed resin demonstrated that the sorption of Hg(II) ions has taken place onto the adsorbent. 9 a SEM of Amberlite IRC86 resin before Hg(II) adsorption 9b of Amberlite IRC86 resin after Hg(II) adsorption EDAX spectrum of Hg(II) loaded resin is shown in 10. The presence of Hg(II) peak in the spectrum confirms the adsorption of Hg(II) onto Amberlite resin. I Research Journal of Environment Sciences__________ Vol. 1(1), 34-41, August (2012) International Science Congress Association Figure-10 SEM- EDAX spectrum of Hg(II) loaded resin Desorption studies: Desorption studies were carried out by treating the spent resin with varying concentrations of HCl (0.1 to 0.5N). It was found that 100% recovery was achieved using 0.5N HCl for 20 and 40 mg/L of Hg(II) solution. The results indicate that adsorption is through ion- exchange mechanism Conclusion Removal of Hg(II) ions from aqueous solution using weakly acidic cation- exchange resin with acrylic skeleton, namely Amberlite IRC86 was found to be very efficient under optimal conditions. The extent of Hg(II) adso rption increases with contact time and resin dose. The kinetics of adsorption process followed pseudo- second order rate equation indicating chemisorption as the rate- limiting step. Equilibrium adsorption data fitted well into Redlich- Peterson isotherm mode adsorption capacity was found to be 70.422 mg/g at 303K. Thermodynamic parameters, S, H and G on the adsorption of Hg(II) indicated that the adsorption process was spontaneous and endothermic. Desorption studies showed that the resin can be regen erated and reused. Thus, the weak acid cation resin with acrylic skeleton, namely Amberlite IRC86 has a very good potential for the removal of Hg(II) from aqueous solution. References 1. Nriagu J.O. and Pacyna J.M., Quantitative assessment of worldwide contamination of air, water and soils by trace metals, Nature, 333, 134 - 139 (1988) 2. Kinhikar V.R., Removal of Nickel (II) from Aqueous Solutions by Adsorption with GranularActivated Carbon (GAC), Res. J. Che. Sci., 2(6) 6-11, (2012) 3. Ma N., Yang Y., Chen S and Zhang Q., Preparation of amine group - containing chelating fiber for thorough removal of mercury ions , J.Hazard. Mater., (2009) Sciences__________ _____________________________ ________ International Science Congress Association EDAX spectrum of Hg(II) loaded resin Desorption studies were carried out by treating the spent resin with varying concentrations of HCl (0.1 to 0.5N). It was found that 100% recovery was achieved using 0.5N HCl for 20 and 40 mg/L of Hg(II) solution. The results exchange mechanism Removal of Hg(II) ions from aqueous solution using weakly exchange resin with acrylic skeleton, namely Amberlite IRC86 was found to be very efficient under optimal rption increases with contact time and resin dose. The kinetics of adsorption process second order rate equation indicating limiting step. Equilibrium adsorption Peterson isotherm mode l. The adsorption capacity was found to be 70.422 mg/g at 303K. G on the adsorption of Hg(II) indicated that the adsorption process was spontaneous and endothermic. Desorption studies showed that the resin can erated and reused. Thus, the weak acid cation -exchange resin with acrylic skeleton, namely Amberlite IRC86 has a very good potential for the removal of Hg(II) from aqueous solution. Nriagu J.O. and Pacyna J.M., Quantitative assessment of worldwide contamination of air, water and soils by trace Removal of Nickel (II) from Aqueous Solutions by Adsorption with GranularActivated Carbon (2012) Ma N., Yang Y., Chen S and Zhang Q., Preparation of containing chelating fiber for thorough , J.Hazard. Mater., 171 288-293 4. Malkoc E. and Nuhoglu Y., Investigations of nickel (II) removal from aqueous solutions using tea factory waste Hazard. Mater, 127 120-128 (2005) 5. Carmona M., Warchol J., A de Lucas and Rodriguez J. Ion- exchange equilibria of Pb on Amberlite IR-120 resin, J.Chem. Eng. (2008)6. Lin L.C., Li J. K and Juang R.S., Removal of Cu(II) and Ni (II) from aqueous solutions using batch and fixed ion exchange processes, Desalination., (2008)7. Lee L. H., Kuan Y.C and Chern J.M., Factorial experimental design for recovering sludge with ion - exchange resin 549-559 (2006)8. Silva R.M.P., Manso J.P.H., Rodrigues J.R.C and Lagoa R.J.L., A comparative study of alginate beads and an ion exchange resin for the removal of heavy metals fr metal plating effluent, J. Environ. Sci. Health 1317 (2008)9. Ramakrishna T. V., Aravamudhan G., Vijayakumar M., Spectrophotometric determination of mercury (II) on ternary complex with Rhodamine 6G and iodide, Chem Acta., 84 369 (1976)10. Aroua M.K., Leong S.P.P., Teo L.Y., Yin C.Y and Daud W.M.A.W., Real- time determination of kinetics of adsorption of lead (II) onto palm shell carbon using ion selective electrode, 99 5786-5792 (2008) 11. Shubha K.., Raji C. and Anirudhan T.S., Immobilization of heavy metals from aqueous solutions using polyacrylamide grafted hydrous Tin (IV) oxide gel having carboxylate functional groups, Water Res., 35 12. Greluk M and Hubicki Z., Sorption on polystyrene anion exchangers: Equilibrium and Kinetics studies, J. Hazard. Mater 13. Shafaei A., Ashtiani F.Z and Kaghazchi T., Equilibrium studies of the sorption of Hg(II) ions onto chitosan, Eng. J.,133 311-316 (2007)14. Chiron N., Guilet R and Deydier E., Adsorption of Cu(II) and Pb(II) onto a grafted silica: Isotherms and Kinetic models, Water Res.,37 3079 – 15. Hasan S.H., Singh K. K., Prakash O., Talat M and Ho Y.S., Removal of Cr(VI) from aqueous solutions using agricultural waste maize bran, 365 (2008)16. Gercel O., Ozcan A., Ozcan A.S and Ferdigercel H., Preparation of activated car bon from a renewable bio of Euphorbia rigida by HSO 4 behavior in aqueous solutions, 4852 (2007) ________ I Res. J. Environment Sci. 40 and Nuhoglu Y., Investigations of nickel (II) removal from aqueous solutions using tea factory waste , J. (2005) de Lucas and Rodriguez J. F., exchange equilibria of Pb 2+, Ni2+ and Cr2+ ions for H J.Chem. Eng. , 53 1325 – 1331 Lin L.C., Li J. K and Juang R.S., Removal of Cu(II) and Ni (II) from aqueous solutions using batch and fixed - bed Desalination., 225 249-259 H., Kuan Y.C and Chern J.M., Factorial experimental design for recovering heavy metals from exchange resin , J. Hazard. Mater., 138 Silva R.M.P., Manso J.P.H., Rodrigues J.R.C and Lagoa R.J.L., A comparative study of alginate beads and an ion - exchange resin for the removal of heavy metals fr om a J. Environ. Sci. Health ., 43 1311 – V., Aravamudhan G., Vijayakumar M., Spectrophotometric determination of mercury (II) on ternary complex with Rhodamine 6G and iodide, Anal Aroua M.K., Leong S.P.P., Teo L.Y., Yin C.Y and Daud time determination of kinetics of adsorption of lead (II) onto palm shell - based activated carbon using ion selective electrode, Bioresour. Technol., and Anirudhan T.S., Immobilization of heavy metals from aqueous solutions using polyacrylamide grafted hydrous Tin (IV) oxide gel having carboxylate 35 300-310 (2001) Greluk M and Hubicki Z., Sorption of SPADNS azo dye on polystyrene anion exchangers: Equilibrium and J. Hazard. Mater ., 172 289 – 297 (2000) Shafaei A., Ashtiani F.Z and Kaghazchi T., Equilibrium studies of the sorption of Hg(II) ions onto chitosan, Chem. Chiron N., Guilet R and Deydier E., Adsorption of Cu(II) and Pb(II) onto a grafted silica: Isotherms and Kinetic – 3086 (2003) Hasan S.H., Singh K. K., Prakash O., Talat M and Ho Y.S., Removal of Cr(VI) from aqueous solutions using agricultural waste maize bran, J.Hazard Mater.,152 356- Gercel O., Ozcan A., Ozcan A.S and Ferdigercel H., bon from a renewable bio -plant 4 activation and its adsorption behavior in aqueous solutions, Appl. Surf. Sci., 253, 4843 - I Research Journal of Environment Sciences_______________________________________________ I Res. J. Environment Sci. Vol. 1(1), 34-41, August (2012) International Science Congress Association 41 17. Kadirvelu K., Faur-Brasquet C and Le Cloirec P., Removal of Cu(II), Pb(II) and Ni (II) onto activated carbon cloth, Langmuir., 8404 – 8409 (2000)18. Sakkayawong N., Thiraveryan P and Nakbanpote W., Adsorption mechanism of synthetic reactive dye wastewater by chitosan, J. Colloid. Interface sci.,256 36 – 42 (2005)19. Reddad Z., Gerante C., Andree Y and Cloirec P., Adsorption of several metal ions onto a low -cost biosorbents: Kinetics and equilibrium studies, Environ. Sci. Technol.,36 2067 – 2073 (2002) 20. Srivastava V.C,.Mall I.D and Mishra I.M., Characterization of mesoporous rice husk ash (RHA) and adsorption kinetics of metal ions from aqueous solution onto RHA, J.Hazard.Mater.,314, 257-267 (2006)21. Dandekar A., Baker R.T.K and Vannice M.A., Characterization of activated carbon, graphitized carbon fibers and synthetic diamond powder using TPD and DRIFTS, Carbon., 36, 1821-1831 (1998)